grandpasob.blogg.se

1. HYDRO GEAR ZT 3100 SERVICE MANUALS
2. HYDRO GEAR ZT 3100 SERVICE INSTALL
3. HYDRO GEAR ZT 3100 SERVICE FULL

If you need a manual and have your Model and Serial Number, click: Get Product Manuals to access the Electronic Manuals Search page. Hydro-Gear Shafts Hydro-Gear Springs Hydro-Gear Transmission Filters Hydro-Gear ZT-2100 Parts Hydro-Gear ZT-2800 Parts Hydro-Gear ZT-3100 Parts Hydro-Gear ZT-3400 Parts Hydro-Gear ZT-5400 Parts View. Please observe all safety precautions featured in the Owner's Manual. Genuine OEM and Aftermarket Hydro-Gear Illustrated Parts Lists available online. * Please see the owner's manual for your unit to identify the correct filter. Transaxle 1015 1027r/50068878 hydro gear zt 5400 powertrain transmission oem. * Approximate Oil Needed is for Complete Drive System, not individual Pumps. Hydro gear genuine transaxle oil service kit. Please see the table below to indentify the correct oil and filter to use with your model. Stop the engine again and check the oil level. Stop the engine and re-engage the bypass levers, and repeat the previous step. Then, purge the system by putting transmission(s) bypass levers in neutral position, then start up the engine and manuever the steering levers forward and reverse slowly, 5 to 6 times. (May take up to 4 qts.)Īll Purging should be completed with the machine at Idle speed, or damage may result

HYDRO GEAR ZT 3100 SERVICE FULL

m) (On transaxle machines only)Īdd Hydraulic Fluid - Pumps & Wheel Motorsįill the reservoir, with the recommended fluid, up to full mark on dipstick.

HYDRO GEAR ZT 3100 SERVICE INSTALL

Install and tighten vent plug to 15 lbf-ft (20.3 N Fill the expansion tank with recommended engine oil until level reaches the cold fill indicator mark on the tank (or dipstick).ģ.

Remove the cap from the expansion tank.Ģ. This Kit Service is an original Hydro Gear OEM part at best price and fast shipping. Note: On transaxles, keep the vent plug open until the oil is filled to mark.įill the reservoir with recommended fluid (about 2 quarts per transaxle on XL, HD, Max Zoom, ProTurn, PT100, & Compacts) (5 quarts per transaxle on PT 200 & 400 models using ZT-5400 transaxles).ġ. Tighten the mounting screws to 5.4 lbf-ft (7.3 N Install the filter guards removed in step 2. Then, tighten oil filter another 3/4 turn.Ħ. Spin new oil filter onto filter housing until it makes contact. Clean the filter mounting surface and then lubricate rubber gasket on new oil filter with clean hydraulic oil.ĥ.

Note: On machines with Pumps and Wheel Motors, oil will only drain out of the reservoir tank, which is all that is required for an oil change.Ĥ. Remove the vent plug (located in between both trans) and allow the transaxle to drain completely (for machines with transaxles only). Remove the filter guard (if equipped) and oil filter from the transaxle (or hydrostatic return line if you have separate Pumps & Wheel Motors).ģ. Sættet indeholder følgende : Gearolie - 5 liter, Oliefiltre - 2 stk, 1 fitting og pumpe. Place container under oil filter to catch oil.Ģ. Service kit med Hydro-Gear´s originale hydrostatolie. NOTICE: Change hydraulic fluid and filter after the first 75 hours of operation and then every 400 hours after.ġ. (20W-50 engine oil may be substituted according to Hydro-Gear's specifications) Use 15W-50 Synthetic Hydraulic Fluid, Ariens Part #00057100